Step 1

Take These Tiles and put them together then your finished 0_o that was quick
Finished Product

Step 1

You have to move bridge u shown here use the 2 tiles at the top as reference to where to shrink it.

Step 2

Fill in the rest of the tiles then you copy and paste the missing segment.

Step 3
Tips
%uFFFDThis type of bridge is mainly for looks since its smaller and uses less space when you want to make some broken bridges
%uFFFDOnly the smallest of units can go through it and even then they have a very tough time
%uFFFDIts good for when you want to save space on your map but of course its hard to maneuver
%uFFFD A good alternative then making collided bridges if your worried about blockiness but if you can do collided right, collided is a better choice

Step 1

First step take this little 2 title and move it to the side doesn't matter if its up or down this is important as a first step as his helps you to remember where to move the rest of the bridge.

Step 2

Fill in the blocks as if it was a regular bridge but moved diagonally as shown here.

Step 3

Fill in the tiles if it was a regular bridge but move it diagonally.

Step 4

Use this as a reference for dirt bridges since you need to extend it for better looks.

Step 1


Make the bridge and use the blends i have right here

Step 2


Use the blend I've displayed at then end to make it blend better.

Step 3


When your done it should look like this

Step 1

First you need to get that little tile in there, remember this as i reference this throughout my tutorial.

Step 2

When you done with that, take the bottom of the bridge and apply it the rest of the similar tiles except the top part that blends with the water, yeah this too its important for some of my peices lol.

Step 3 (High Dirt/Ruins)
Now you have to choose either ruin bridge or high dirt, for high dirt simply fill in any bridge with high dirt (rectangular).
And the for ruins bridge just use this title group.

Finished Bridges


Ruins Bridge


High Dirt


A Finished Product Utilizing this.

Do Step 1 of the high dirt bridge then apply this cliff terrain to the piece

Step 1

You also have to apply the front of the cliff tile at the bottom and top to make it look better (optional).

Step 2


make sure the bridge is a little widen compared to the one in the doodad database so that the bottom part can fit better.

Step 3

Do step 2 (ruins/high dirt bridge) above then use this title combination.

Finished Dirt Bridges

Step 1

Start with a regular bridge and try to make it bended (look at side bridge for reference)
Then you use the bridge title I've selected in this picture.

Step 2

When your done is should look something like this and as you see i used some collided bridges here, oh and i forgot to use the darker tiles for the front (top right-ish) you should see the colors clashing

You have to remember that the bridges are both mirrored meaning if you have the same block but in the opposite direction of it blends, you put it together to create this blend.

Step 1

Find any two mirrored tiles

Step 2


Put them together and then add some of the bridge blend

Same as above but left and right
Take theses two blends and place em together

Step 1

Bottom


Top


Then add em together to get this


Step 2

Apply to a piece

Step 1

Carefully plan out where you collided bridges are going to go make sure there' s enough room to place the bridge *note how i try to make a section intertwine...


Step 2

take out any thin blocks meaning the ones less then the isometric 1 (this only applies to where your bridge is going to go) or make it thicker


Step 3

Apply the outline of your bridge to your liking.The most vital block is the cliff block you should see it when you look at the bridge (not hard to figure out)

Don't forget to add this block to the side


Step 4

I tried to make step 4 have alot of problems people face if you look close at 3 and 4 you can notice the changes...



Step 5

if you look at the bottom right you see instead of the dirt tile from the bridge i use the bridge itself either way works it mainly depends on your presences, some terrain work with it but most don't, this one was very rushed and didn't get mesh well so i had t get creative, on a final note you can't just follow a guide to do this you have to know all these tips by heart and altar your terrain to your specific terrain piece/map.
Finished Product...

Step 1

Firstly Remove the part above and below the bridge as it only gets in the way or keep depending what you want to make...
Unfortunate this type of blend is 100% of the time is block or is way too large.

Step 2
Make some random designs here are a few i've made/found.


One from a map i had lying around ill give it to by special request,


One terrain piece i sent for terrain hall of fame

http://i33.tinypic.com/302crjt.jpg - Sorry image failed to get size 0.o
One I made in about an hour ago

Tips
•Try and make it look organized since the more random you get the more blocky the bridge tend to get.
•If you go over the borders try to adapt some of the v formation of the dirt bridge (you should of course make sure its large enough), if you want to have a bridge of a certain size you'll probably have to sacrifice looks for gameplay
• don't forget about step 2 from the beginning (2 title combination) as it will help you for sometimes when it looks blocky
•remember to put that high dirt title if you have any title or ruins in the bridge

0_o Tempz < Payne = Ban Hammer